Who Builds Your Liquid Filling Machine?
Most of our core machines are made in our own factory. Your quotation names who builds this model, the filling heads and what is tested before shipment.
Perfume, toner and essence are thin liquids, and they drip, foam or fill unevenly when the filler is wrong for them. Our two level fillers cover bottles from 10 to 500 mL.
Request a QuoteView Photos

A level filler runs liquid into the bottle until it reaches a set height, so every bottle shows the same fill line even when the glass varies a little. The four-head vacuum model fills bottles from 10 to 500 mL. The single-head pneumatic model fills 10 to 300 mL and needs only compressed air.
Typical liquids are perfume, florida water, mosquito repellent, toner, essence and drinks. Creams, gels and pastes are too thick for these machines. For fills of 1–20 g of oil or paste, look at our essential oil filling machines instead.
Discuss Your ApplicationSend a sample, a container or a photo of what you make. We reply with the machine we would look at first, and what we still need to confirm.
Request a Quote
Answer these before you ask for a quote.
Most of our core machines are made in our own factory. Your quotation names who builds this model, the filling heads and what is tested before shipment.
Both machines are built for thin, free-flowing liquids. Lotions, gels and pastes are too thick; send the viscosity and we tell you what to look at.
The vacuum filler covers 10–500 mL and the single-head filler 10–300 mL. A fill under 10 mL belongs on a small-bottle filler.
The vacuum filler takes bottles 7–100 mm across and 50–300 mm tall. The single-head takes 6–25 mm across. Send a bottle and we check the neck.
Send the liquid, its viscosity and one bottle. We say whether a level filler fits or what else to look at.
The two models side by side. Your quotation confirms the configuration you order.
Two models cover thin-liquid filling.
| Parameter | 4-Head Vacuum | Single-Head Pneumatic |
|---|---|---|
| Fill volume | 10–500 mL | 10–300 mL |
| Bottle diameter | 7–100 mm | 6–25 mm |
| Bottle height | 50–300 mm | 50–200 mm (custom) |
| Speed | 40–60 bottles/min | 10–25 bottles/min |
| Power | 220 V / 50 Hz, 0.2 kW | Compressed air 0.4–0.6 MPa |
| Size (mm) | 750 × 600 × 1600 (standard) | 230 × 390 × 620 |
The liquid decides the filler.
| Parameter | What We Check |
|---|---|
| Type | Perfume, toner, essence, florida water, mosquito repellent and drinks are typical. |
| Viscosity | Send a figure, or tell us whether it pours like water or like oil. Thicker liquids need a different filler. |
| Solvents | Alcohol and other flammable solvents need an electrical and safety review before we quote. |
| Foam | Foaming liquids fill slower. Tell us if yours foams. |
Settle the utilities before you order.
| Parameter | What We Check |
|---|---|
| Electrical | The vacuum model needs 220 V, 50 Hz and 0.2 kW. Tell us your supply. |
| Air | The single-head model needs 0.4–0.6 MPa of compressed air. |
| Footprint | The vacuum model is about 750 × 600 mm on the floor; the single-head about 230 × 390 mm. |
| Spills | Put a drip tray under the heads and plan how you clean between liquids. |
Agree the check with your own bottles.
| Parameter | What We Check |
|---|---|
| Level | Fill a batch of your bottles and compare the liquid level from bottle to bottle. |
| Drips | Check the neck and the outside of the bottle after the head lifts. |
| Foam | Run at your normal speed and watch the neck. |
| Records | Agree before you order whether a test video or record ships with the machine. |
Loading and flushing often limit output.
| Parameter | What We Check |
|---|---|
| Speed | The vacuum filler runs 40–60 bottles a minute and the single-head 10–25. |
| Loading | The vacuum filler takes four bottles at a time, loaded by hand, so your loading speed sets the real pace. |
| Flush | Allow time to flush the line between liquids. |
A pump filler is a different machine for thicker liquids. It is here so you can see where our two models stop.
| This EquipmentVacuum Filler | Single-Head Filler | Pump Filler | Hand Filling | |
|---|---|---|---|---|
| Liquid | Thin | Thin | Thicker, creamy | Any |
| Fill method | Level by vacuum | Level by air | Set volume by pump | By eye |
| Power | Electric | Compressed air only | Electric | None |
| Best for | Steady production | Small runs and low power | Creams and gels | Samples |
| Check first | Bottle height and width | Bottle under 25 mm across | Viscosity | Consistency from bottle to bottle |
Four typical jobs and what to settle first.

Vacuum filling brings every glass bottle to the same line, even when the bottles vary a little. If your perfume is alcohol-based, we review the electrical and safety side before we quote.
Discuss This Application
Thin skin-care liquids fill well by level. The vacuum filler takes bottles from 50 to 300 mm tall; send yours so we can check the fit.
Discuss This Application
The single-head filler needs no electrical supply, only compressed air. It suits a workbench, a trial run or a site with limited power.
Discuss This Application
For small bottles and a steady flow, our essential oil line fills 20–40 a minute on a conveyor. See the essential oil filling machines.
Discuss This ApplicationThe questions buyers ask before they order.
Write the test liquid, the pass criteria and what ships with the machine into the quotation.
Discuss Acceptance CriteriaWith these details we can say whether a level filler fits your liquid.
Have another material or format?
Share your requirements.
Send your liquid, bottle and bottles per hour.
We say whether the vacuum, the single-head or another filler fits.
Agree a fill test with your liquid.
Review the price, the liquid filling machine configuration and terms.
Run the checks you agreed on the liquid filling machine, then pack and ship.
Not well. These fillers are built for thin, free-flowing liquids. For a lotion or gel, send the viscosity and we tell you what we would look at.
Level filling stops when the liquid reaches a set height in the bottle. Volume filling pumps a measured amount. Level fill looks even on the shelf; volume fill matches the volume on the label.
Drinks are among the liquids this type of filler is used for. Tell us the exact drink and we confirm that the parts touching the liquid suit it.
The single-head model does, at 0.4–0.6 MPa. The vacuum model runs on 220 V electricity. Tell us what you have.
Flush the line with a cleaning liquid that suits your product, and allow for the flush time in your output plan. Ask us for the cleaning steps for your liquid.
Tell us the liquid and the bottle first. Add the rest when you have it.
Send the liquid, its viscosity and a bottle. We reply with the filler we recommend.
Get a Quote