Who Builds Your Perfume Pump Pressing Machine?
Our own factory builds most of our core machines. Build quality and delivery are our responsibility under the order terms.
Perfume pump pressing is where long dip tubes bend and collars sit crooked. Our pneumatic press seats collars at 20 to 40 bottles a minute, and a dip tube cutter, available on request, trims tubes to 40 to 300 mm first.
Request a Quote

Before a sprayer goes on, its dip tube has to match the bottle depth. The dip tube cutter, an extra machine we quote on request, cuts tubes up to 10 mm in diameter to lengths of 40–300 mm with an alloy tool steel blade. The pneumatic cap press then seats the pump collar, at 20–40 bottles a minute.
The press covers bottles 15–300 mm tall, and the press range of 10–50 mm can be customized. Both run on compressed air at 0.4–0.6 MPa with a small footprint, so they fit a bench.
Discuss Your ApplicationThese four points decide which setup fits.
Our own factory builds most of our core machines. Build quality and delivery are our responsibility under the order terms.
A flat cut helps the tube seat at the bottle base. The cutter uses an alloy tool steel blade.
The 10–50 mm press range can be customized, which helps with odd collar sizes.
Press height adjusts for bottles from 15 to 300 mm.
Send the pump with its dip tube and the bottle. We confirm the cutter and press.
The cap press and the dip tube cutter side by side.
Two small machines work together. The cutter is an extra machine we quote on request.
| Parameter | Pneumatic Cap Press | Dip Tube Cutter (on request) |
|---|---|---|
| Action | Presses pump collars | Cuts dip tube to length |
| Speed | 20–40 bottles/min | Cut on demand |
| Capacity | Press range 10–50 mm (custom) | Tube up to 10 mm; length 40–300 mm |
| Bottle height | 15–300 mm | Not applicable |
| Power | Air 0.4–0.6 MPa | Air; pneumatic valve |
| Size (mm) | 250 × 230 × 550 | 200 × 300 × 440 |
The pump decides the press.
| Parameter | What We Check |
|---|---|
| Collar | The collar diameter must fall within the 10–50 mm range. |
| Tube | The tube diameter can be up to 10 mm. |
| Length | The cut length runs from 40 to 300 mm. |
| Height | The height of the actuator affects press clearance. |
| Parameter | What We Check |
|---|---|
| Space | The press is about 250 × 230 mm and the cutter 200 × 300 mm. |
| Air | Both machines need 0.4–0.6 MPa of compressed air. |
| Waste | Keep a bin for the tube offcuts. |
Test seating and spray.
| Parameter | What We Check |
|---|---|
| Seating | The collar should sit flush with the neck. |
| Height | The pump height should be even across a batch. |
| Spray | Spray a batch and check the pattern and any leaks. |
| Tube | The tube should touch the bottle base without bending. |
Cutting is quick; pressing paces the line.
| Parameter | What We Check |
|---|---|
| Press speed | The press runs 20–40 bottles a minute. |
| Cutting | Cut the tubes before pressing, in batches. |
| Next step | Crimping or labeling comes after pressing. |
Pressing next to crimping and capping.
| This EquipmentCap Press | Perfume Crimper | Bottle Capper | Dip Tube Cutter (on request) | |
|---|---|---|---|---|
| What it does | Presses pump collars | Crimps metal collars | Screws caps | Cuts tubes |
| Speed | 20–40/min | 15–40/min | 25–90/min | On demand |
| Power | Air | Air | Electric or air | Air |
| Best for | Press-fit collars | Crimped sprayers | Threaded caps | Trimming tubes |
| Check first | Press range | Collar size | Cap thread | Tube diameter |
Four steps around pump pressing and the machine for each.

The press does 20–40 bottles a minute and adjusts for the bottle height.
Discuss This Application
Cut tubes up to 10 mm across to 40–300 mm. Send your pump.
Discuss This Application
Metal collars need a crimper instead of a press. Send your collar and we tell you which one you need.
Discuss This Application
An air bottle washer, available on request, cleans 20–40 bottles a minute.
Discuss This ApplicationWhat perfume makers ask before they order a pump press.
Write the test method, the pass criteria and what ships with the machine into the quotation.
Discuss Acceptance CriteriaWith these details we can confirm the cutter and the press.
Have another material or format?
Share your requirements.
Send a pump, a bottle and your bottles per hour.
We confirm the cap press and, if you need it, the dip tube cutter.
Agree a seating and spray test.
Review the price, the perfume pump pressing machine configuration and terms.
Run the checks you agreed on the perfume pump pressing machine, then pack and ship.
It is seating the sprayer collar onto the bottle neck. A press does this with controlled force instead of by hand.
Not quite. Pressing seats a collar; crimping deforms a metal collar around the neck. Some bottles need one, some the other.
If your tubes arrive long, yes. The cutter is available on request and trims to 40–300 mm so the tube meets the bottle base.
No. Both run on compressed air at 0.4–0.6 MPa.
Yes. The 10–50 mm press range can be customized. Send your collar.
Tell us the pump and the bottle first. Add the rest when you have it.
Send a pump with its dip tube and a bottle. We confirm the cutter and the press.
Get a Quote